Thursday, July 7, 2011

Radiator full

Chipped away at a number of things today to get ready for the firing of the motor. Remade the tensioner bracket - first pass wasn't up to my quality standards.

This afternoon I ordered up a new tensioner, and got hoses so I could fill the radiator. I know the block is full - didn't have the rear caps on the steam ports, and got the water level up that far. Doh!. The cooling system is now water tight and full. I still need to figure out where to mount the expansion tank - hose routing makes sense on the driver's side, but with headlight and fan relays, and the brake booster, that side is a bit congested.

The fuel system is now ready for a pressure test. I put in a new fuel filter, hooked up the lines from the tank after replacing a line, and tightened all the fittings.

Still to do - finish the front dress, hook up power steering lines, replace spark plugs, finish hooking up the wiring, hook up the oil pressure gauge, and measure and set the fuel pressure to 58 PSI.
Posted by Picasa

Wednesday, July 6, 2011

Fuel at 90%

Took Sunday and Monday off to enjoy the holiday weekend. Went back at it yesterday, spending the whole day wiring in fuse blocks and relays for the engine harness. I think it's pretty close to ready to hook up and test.

Here's the lower hose in place.



And the upper hose, snaked away from where the air intake will be.


Here's the modified truck rails with AN fittings joining the pieces together.



And here's most of today's effort, putting in the Aeromotive fuel regulator. I'll need to put a safety shield in front of this, since the lines are in the direct path of projectiles from the front tire.

Engine got oil today. Tomorrow it's time to start filling the cooling system.
Posted by Picasa

Sunday, July 3, 2011

1961 Corvette, 5.3L radiator hoses

Went to the local parts store to get hoses for the Corvette. Didn't even bother to say I needed hoses for a 1961 Corvette with a 5.3L motor. Just handed the parts guy the four bends I had pulled together from yesterday's test fit, and said find me two hoses with two of these bends each. Within 10 minutes I was walking out of the store with the two hoses, and with part numbers for future reference for the next hose replacement.

Posted by Picasa

Saturday, July 2, 2011

Toolmaking and tubing

I'm on vacation for the next week, and my primary focus on the car will be to get it to a point that it will fire up. Small matters such as a cooling system, fuel system, and electrical systems need to be finished up. In prep for this, I made a trip to Burns Stainless in Costa Mesa to drool over some headers and pick up some Aluminum maderal bends for the cooling system and for the intake track from the filter to the MAF to the throttle body. I also picked up some 3 1/2 silicon hose to connect part of the track together.

I also made a stop at Mesa Hose to get the AN fittings brazed on my fuel lines for the crossover between the fuel rails and for the supply line. I also had a piece of 1/2 stainless tubing bent to join the two sections. I installed tube nuts and flared that tube myself.

Here's the two radiator lines. The long one is 1 3/8 tube, the 45 is 1 1/2 tube. I cut them to length, then made a bead with my new custom beading tool.

Here's the final section of the intake. Before was a section of steel 3 1/2 tube and a section of hose. I'm replacing that with 3 1/2" aluminum tube and a silicon hose section to join the to the rest of the system.

Here's the rest of the system. The black section and section with the concave portion were from the old system. I trimmed the black piece to get room for the MAF.

Here's the section that will go to the throttle body. It starts with a 4" manderal bend, then goes to the MAF, then to a straight section of 4" tube, then to a 4 to 3 1/2 silicon reducer. The straight section off the MAF had to be expanded to take the transition to the MAF.

Here's my beading tool. I used a couple pieces of angle iron for the swing arm and the base plate. I bolted a couple round sections with grooves for the base. The action part of the tool is a couple washers on a half inch bolt, with a sleeve to space it to the grooves, bolted to the other piece of angle iron.

Arbor ready to come down on the tool.

Here it is with a sample of tube on it. We only mashed one practice piece.

Here's a shot in the arbor press.

A close up of the press arm coming down on the beading tool.

Posted by Picasa

Saturday, June 11, 2011

slow going



Spent pretty much a full day in the garage today. Installed outer door handles in both doors. Installed the mirror bracket on the driver's door, and the antenna on the rear fender. Started putting the nuts on the top fender trim and decided it needs to come off to open up a hole slightly so it's not so forced.

Most of the time today was in the dash area. Pulled the column and reinstalled with all the gaskets in place. Put the column/dash support in place. Put the dash in place, but still need to bolt down. Glued the dash pad and put the defroster vents in place. Put more wiring from the engine harness through the firewall. So much more to do.
Posted by Picasa

Saturday, June 4, 2011

Reassembly Day One

The car came home yesterday, and I started a couple things last night, but not much. I got the left hand rear bumper brackets in place, but realized the right side would have been a whole lot easier before we bolted the body last week. Had to unbolt some of the right side body bolts and lift the body to get the right side brackets in place.


Along with putting on the bumper brackets, we cleaned the taillights and I mounted them, and we cleaned the chrome around the licence plate, and I installed the back bracket, license plate and the chrome. I also put the trunk lock in place.


The interior took the bulk of the time today, mostly in putting in seven sheets of dynamat and taping all the seams with aluminum tape. I started running the engine harness into the interior - I'll put the PCM on the tranny tunnel. Soon I'll want to get the instrument cluster in place so I can start the remaining wiring and get key gauges hooked up so I can fire the engine.
Posted by Picasa

Friday, June 3, 2011

Home at last

Took a late lunch today and had a tow truck meet me at the shop to get the car home. Tow truck driver rolled her right off the truck and on to the lift. All good.

Posted by Picasa